一级特黄视频-一级特黄aa大片欧美-一级片mp4-一级毛片直接看-久久99热在线观看7-久久99热狠狠色一区二区

Welcome to the official website of Legret Metal Company
Focus on electronic welding for 20 yearsDONGGUAN LEGRET METAL.,LTD
National consultation hotline:135-2799-2739
Contact US
mobile phone: 135-2799-2739
Service hotline: 0769-38893080
Email: lzd@dglzd.com
Address: Dongguan lvzhidao Metal Co., Ltd
Contact person: Manager Zeng
Industry information

What are the characteristics of reflow welding, one of the common welding methods of electronic components?

作者:Solder manufacturer 2021-03-08 0

In the production process of electronic products, there are two common welding methods of electronic products, which are called reflow soldering and wave soldering;


The difference between the two welding methods is that the wave peak welding is mainly used to weld the plug-in circuit board, while the reflow welding is mainly used for SMT chip board welding.


Reflow welding process is to realize the soldering of mechanical and electrical connection between the welding end of surface assembly components or pins and the solder pad of printed board by remelting the paste solder which is pre distributed to the pad of printed board.


Reflow welding can control the amount of solder applied in the leading process, effectively reduce the incomplete defects of solder, such as false welding and bridge welding, so as to make the welding quality stronger, the weld joint consistency better and the reliability is very high.


During the process of electronic processing, the reflow welding does not directly dip the component into the molten solder, so the component is subject to small thermal impact (because the heating mode of reflow welding is different, in some cases, the temperature applied to the components will be higher, and the thermal stress of the corresponding components will be relatively large).


The solder for reflow welding is a commercial solder paste. It can ensure the normal composition when ordering, and it will not mix impurities in general, and it is easier to ensure the quality of welding.


If the position of solder applied on PCB is correct in the leading process and the position of the sticking component deviates from that of the component, during the reflow welding process, when all the welding ends, pins and corresponding pads of the components are wet at the same time, the effect of the surface tension of the molten solder will produce self setting effect, which can automatically correct the deviation and pull the components back to the approximate accurate position.


Local heating heat source can be used, so different welding methods can be used on the same substrate.


The process is relatively simple, and the workload of repairing electronic components is very small when the defective products appear.


主站蜘蛛池模板: 含羞草传媒在线观看| 国产综合在线视频| 欧美特级另类xxx| CHINA学生白嫩| 欧美卡1卡2卡三卡2021精品| wwwxxx日本护士| 色综合伊人色综合网站下载| 国产成人高清视频| 亚洲精品嫩草研究院久久| 久久大胆视频| 97亚洲狠狠色综合久久久久| 欧美午夜精品A片一区二区HD| 波多野结衣的AV一区二区三区| 乳色吐息在线观看全集免费观看| 国产AV亚洲精品久久久久软件 | 欧美含羞草免费观看全部完| xxx成熟xxx| 午夜性伦鲁啊鲁免费视频| 久久99国产精品自在自在| 99免费在线观看| 色欲蜜臀AV免费视频| 黑丝袜论坛| 99精品免费久久久久久久久日本 | 国产精品久免费的黄网站| 亚洲男女羞羞无遮挡久久丫| 老师给美女同学开嫩苞| YELLOW日本免费观看播放| 香蕉59tv视频| 啦啦啦WWW在线观看免费高清版 | 高H高肉强J短篇NP| 亚洲精品久久7777777| 免费看国产曰批40分钟| 国产精品青青在线麻豆| 4hu四虎免费影院www| 色综合精品无码一区二区三区| 久久精品亚洲AV中文2区金莲 | 父亲猜女儿在线观看| 一个人的HD高清在线观看| 日本一卡精品视频免费| 精品国产精品人妻久久无码五月天| 伧理片午夜伧理片|